Do you work in the event industry?
If so, please call us toll free 877.321.1999 (out of US: +1.504.522.0300) for wholesale pricing for the above and other products.
About the Product
FINALLY, an affordable battery-operated small tabletop remote control confetti cannon. You can rent it with either a push button control unit or a wireless transmitter. Our transmitter has a unique numeric code to prevent misfires. Our transmitter can be programmed to fire multiple small tabletop remote control confetti cannons off at once or in a staggered firing configuration.
Your guests will be surprised and “WOWED!" as the battery-operated tabletop confetti launcher explodes with magic and fun! Another fabulous Flutter FETTI® product to make you, the Event Planner, "dazzle" in your client's eyes! Consider putting a small tabletop remote control confetti cannon in all the centerpieces at a wedding, bar, or bat mitzvah. Or at your next stage production position them down stage and fire Silver Metallic Flutter FETTI in the barrels which will simulate a “ sparkler" special effect. Or in a Nightclub hide one under a napkin on a tray so when the BIG BOTTLE is presented to the guest the table top explodes showering the guest and his friends with added excitement!
The small tabletop remote control confetti cannon is 14” inches tall and 4.5” X 4.5” at the base. It weights approximately 4 Lbs. when the barrel is filled with a Flutter FETTI product. Remember if your going to hide it you much have access to it to be able to screw in the Co2 cylinder and to press the ON button on the black box control unit.
Rental unit (with push button control unit) comes with
- Pedestal stand
- Launcher barrel (Pre-loaded with the Flutter FETTI product you requested.)
- Receiver
- 8-gram threaded Co2 cylinder
- Push button control unit
Rental unit (with wireless transmitter)
- Pedestal stand
- Launcher barrel (Pre-loaded with the Flutter FETTI product you requested.)
- Receiver
- 8-gram threaded Co2 cylinder
- Transmitter
Please call us for rental information Toll Free: 877-321-1999
The Table Top Launcher is made in the USA.
Remember if your shipping box doesn't have the Flutter FETTI Official Product Seal on the outside of the box it's NOT and Authentic Certified Flutter FETTI product!
Disclaimer: Note some confetti products are colored with dye that may stain if they come become damp or wet. Please remove wet confetti immediately upon discharge.
© 2022 Parti Line International, LLC. All Rights Reserved
Instructions For Use
INSTRUCTIONS FOR USE
PUSH BUTTON CONTROL UNIT
STEP 1- This system comes with 3 parts; the launcher base and valve, the power pack and a push button detonator. On the top of the power pack there are 2 outlets for connectors. One is for the wire coming from the launcher and the other accommodates the push button detonator. When attaching these, be careful to get the right connector in the right outlet. One connector has 2 pins and the other one has 3 pins. Check the pins on each wire and line them up to the right connector. When the correct pins are identified, place the connector on the top of the corresponding outlet and gently twist the connector back and fourth until it lines up with a keyway (a keyway is a tongue and grove). Once lined up o the keyway you can push down for a firm connection and twist the outer locking ring on the connecting wire. Repeat for both the launcher and push button connectors. (PLEASE WATCH THE INSTRUCTIONAL VIDEO FOR ADDITIONAL INFORMATION.)
STEP 2 - In preparation for firing, attach the barrel to the correct port on the launcher by pulling the spring load outer ring on the launcher port downward. Insert the barrel into the port firmly. Let the spring loaded ring pop up to lock the barrel in place. Pull the barrel upward to make sure it is locked into place.
STEP 3 - Screw the 8 gram threaded Co2 cylinder into the other launcher port. You will feel resistance as you screw down but keep screwing the Co2 cylinder in quickly. As the Co2 cylinder is pierced a small amount of gas will escape. Keep screwing down until all the gas stops leaking. That small amount of escaping gas will not effect the shot. You should feel a slight temperature drop when fully screwed down.
Next push the button on the front of the black power pack, hoLD for 2 seconds then release. The LED light in the front of the box should now blink red or green, the color makes no difference.
STEP 4 - When ready to fire, push the RED BUTTON on top of the detonator and the launcher barrel will fire instantaneously.
INSTRUCTIONS FOR USE
when using the WIRELESS SYSTEM
STEP 1 - In preparation for firing, attach the launcher barrel to the correct launcher port on the side of the base by pulling the spring loaded outer ring downward. Insert the barrel into the port firmly. Let the spring loaded ring pop up to lock the barrel in place. Pull the barrel upward to make sure it is locked in place. (PLEASE WATCH THE INSTRUCTIONAL VIDEO FOR ADDITIONAL INFORMATION.)
STEP 2- Screw the 8 gram threaded Co2 cylinder into the other launcher port. You will start to feel resistance as you screw down. Keep screwing quickly. As the Co2 cylinder is pierced a small amount of gas will escape. Keep screwing down until all the gas stops leaking. That small amount of gas escaping will not effect the shot. You should feel a slight temperature drop when fully screwed down.
STEP 3 - The following step should be performed 5 TO 10 MINUTES BEFORE THE LAUNCH QUE.
Push the button on the front of the black receiver until the LED light starts to blink either a red or green light. The color makes no difference. Turn on the transmitter by pushing the LARGE RED BUTTON on the LEFT SIDE. In the screen of the transmitter you will be asked for a code. ENTER CODE 7,9,2.
STEP 4 - To arm, press the W BUTTON, the read out in the transmitter window will say 1 arm or 2 disarm. Press 1 for arm, then all the receiver lights should be on steady. If all the receiver lights are not burning steady, push the CANCEL button and try again.
STEP 5 - When ready to fire, press G, then 1 then send. When you release the send button the launchers should all start firing in the sequence you requested. Firing is instantaneous, unless you asked for delayed programming. Sequencing or delay firing is preprogramed at the factory per your request.
ASSISTANCE - PLEASE CONTACT OUR TECHIE AT 504-251-6312. If no answer leave a message and he’ll call you back. We suggest ONCE THE TABLE TOP ARRIVES YOU CALL OUR TECHIE to do a complete run through BEFORE the day of your event.
RELOADS REQUIRED FOR THE SMALL TABLETOP REMOTE CONTROL CONFETTI CANNON
- Metallic Flutter FETTI or Metallic FETTI Strips
- Tissue Flutter FETTI
- Tissue Corkscrews
- Compression Tape
- 8-Gram Threaded Co2 cylinder
- 7/8" Compression Cap